TPI to millimetre pitch
Inch threads are measured in threads per inch (TPI); metric threads by pitch, the distance from one crest to the next in millimetres. Pitch in mm = 25.4 ÷ TPI. The last column gives the closest metric pitch; marked pairs are close enough that a gauge can be fooled, but not close enough to interchange.
| TPI | Pitch mm | Pitch in | Unified threads | Nearest metric pitch |
|---|---|---|---|---|
| 80 TPI | 0.318 mm | 0.0125 | #0-80 | 0.3 mm (near-identical) |
| 72 TPI | 0.353 mm | 0.0139 | #1-72 | 0.35 mm (near-identical) |
| 64 TPI | 0.397 mm | 0.0156 | #1-64, #2-64 | 0.4 mm (near-identical) |
| 56 TPI | 0.454 mm | 0.0179 | #2-56, #3-56 | 0.45 mm (near-identical) |
| 48 TPI | 0.529 mm | 0.0208 | #3-48, #4-48 | 0.5 mm |
| 44 TPI | 0.577 mm | 0.0227 | #5-44 | 0.6 mm |
| 40 TPI | 0.635 mm | 0.0250 | #4-40, #5-40, #6-40 | 0.6 mm |
| 36 TPI | 0.706 mm | 0.0278 | #8-36 | 0.7 mm (near-identical) |
| 32 TPI | 0.794 mm | 0.0313 | #6-32, #8-32, #10-32 | 0.8 mm (near-identical) |
| 28 TPI | 0.907 mm | 0.0357 | #12-28, 1/4-28 | 1 mm |
| 24 TPI | 1.058 mm | 0.0417 | #10-24, #12-24, 5/16-24, 3/8-24 | 1 mm |
| 20 TPI | 1.270 mm | 0.0500 | 1/4-20, 7/16-20, 1/2-20 | 1.25 mm |
| 18 TPI | 1.411 mm | 0.0556 | 5/16-18, 9/16-18, 5/8-18 | 1.5 mm |
| 16 TPI | 1.588 mm | 0.0625 | 3/8-16, 3/4-16 | 1.5 mm |
| 14 TPI | 1.814 mm | 0.0714 | 7/16-14, 7/8-14 | 1.75 mm |
| 13 TPI | 1.954 mm | 0.0769 | 1/2-13 | 2 mm |
| 12 TPI | 2.117 mm | 0.0833 | 9/16-12, 1-12, 1-1/8-12, 1-1/4-12, 1-3/8-12, 1-1/2-12 | 2 mm |
| 11 TPI | 2.309 mm | 0.0909 | 5/8-11 | 2.5 mm |
| 10 TPI | 2.540 mm | 0.1000 | 3/4-10 | 2.5 mm |
| 9 TPI | 2.822 mm | 0.1111 | 7/8-9 | 3 mm |
| 8 TPI | 3.175 mm | 0.1250 | 1-8 | 3 mm |
| 7 TPI | 3.629 mm | 0.1429 | 1-1/8-7, 1-1/4-7 | 3.5 mm |
| 6 TPI | 4.233 mm | 0.1667 | 1-3/8-6, 1-1/2-6 | 3.5 mm |
Metric pitch to TPI
| Pitch | TPI equivalent | Metric threads with this pitch |
|---|---|---|
| 0.25 mm | 101.60 | M1, M1.2 |
| 0.3 mm | 84.67 | M1.4 |
| 0.35 mm | 72.57 | M1.6 |
| 0.4 mm | 63.50 | M2 |
| 0.45 mm | 56.44 | M2.5 |
| 0.5 mm | 50.80 | M3 |
| 0.6 mm | 42.33 | M3.5 |
| 0.7 mm | 36.29 | M4 |
| 0.8 mm | 31.75 | M5 |
| 1 mm | 25.40 | M6, M8, M10 |
| 1.25 mm | 20.32 | M8, M10, M12 |
| 1.5 mm | 16.93 | M10, M12, M14, M16, M18, M20, M22 |
| 1.75 mm | 14.51 | M12 |
| 2 mm | 12.70 | M14, M16, M24 |
| 2.5 mm | 10.16 | M18, M20, M22 |
| 3 mm | 8.47 | M24, M27 |
| 3.5 mm | 7.26 | M30 |
Measuring an unknown thread
- Measure the major diameter across the crests with calipers. Bolts read slightly under nominal: a 1/4 in bolt often reads 0.245–0.248 in, an M6 bolt 5.85–5.95 mm.
- Hold a ruler along the thread and count the crests in 1 in. 20 crests is 20 TPI. For metric, count over 10 mm and divide 10 by the count.
- Better: try a thread pitch gauge leaf; the right one sits with no light under it. Check both an inch and a metric leaf, because 20 TPI (1.27 mm) and a 1.25 mm metric pitch look alike in the hand.
- Search the diameter and pitch here to name the thread and get its tap drill.
Look-alike pairs: 24 TPI is 1.058 mm, close to M6 × 1 (1 mm) over a short length; 13 TPI is 1.954 mm, close to 2 mm. A nut will start on the wrong one and then bind after a couple of turns. If it binds, stop: it is the wrong thread.
Sources: Wikipedia, "Unified Thread Standard" (UNC / UNF series, number-screw diameters); Wikipedia, "ISO metric screw thread" (ISO 261 coarse and fine pitches, basic profile).