Skip to the chart
drillbitsizechart

NPT Thread Chart

Pipe size, real outside diameter, threads per inch and tap drill for every NPT size to 2 in. Measured a fitting? Type the OD to find the size.

Try

1/2 NPT

23/32tap drill14TPI0.84pipe OD, in

Tap drill
23/32 0.7188 · 18.26 mm
Pitch
0.0714 in = 1.814 mm
Pipe OD
0.8400 in = 21.34 mm. The name is not the OD: a 1/2 pipe measures 0.84 in
Taper
1 in 16 on diameter (3/4 in per foot, 1.79° per side)

NPT pipe thread chartthe size is not the OD

SizeTPIOD inOD mmTap drillDrill mm
1/16270.3137.95ask the tap maker—
1/8270.40510.29R 0.33908.61
1/4180.5413.727/16 0.437511.11
3/8180.67517.1437/64 0.578114.68
1/2140.8421.3423/32 0.718818.26
3/4141.0526.6759/64 0.921923.42
111.51.31533.41-5/32 1.156329.37
1-1/411.51.6642.161-1/2 1.500038.1
1-1/211.51.948.261-47/64 1.734444.05
211.52.37560.322-7/32 2.218856.36

NPT sizes, OD, TPI and tap drills

The pipe size is a name, not a measurement: 1/2 in NPT has an outside diameter of 0.840 in. That is the most common mix-up with pipe threads. If you measured the thread with calipers, type the measurement in the box above and the chart finds the pipe size from the OD.

Pipe sizeODOD mmTPITap drillDrill in
1/160.313 in8.0 mm27——
1/80.405 in10.3 mm27R0.3390
1/40.540 in13.7 mm187/160.4375
3/80.675 in17.1 mm1837/640.5781
1/20.840 in21.3 mm1423/320.7188
3/41.050 in26.7 mm1459/640.9219
11.315 in33.4 mm11.51-5/321.1563
1-1/41.660 in42.2 mm11.51-1/21.5000
1-1/21.900 in48.3 mm11.51-47/641.7344
22.375 in60.3 mm11.52-7/322.2188

The 1/16 NPT tap drill varies by source and is left blank; most charts give 1/4 in or letter D, and the tap maker's figure should win. Tap drills are for drilling without a reamer; with a 1:16 taper pipe reamer, drill one or two sizes smaller.

The taper

parallel linetaper 1 in 16 on the diameter = 3/4 in per foot (angle 1°47′ per side, exaggerated here)pipe end (small)
NPT threads taper 1 in 16 on the diameter: 0.0625 in per inch of length. The seal comes from the flanks wedging together, helped by tape or sealant.

Because the thread is tapered, a tapped NPT hole has no single "depth"; it is tapped until a fitting threads in a set number of turns by hand. The usual target is hand-tight engagement of about 4 to 5 turns on 1/2 and 3/4 in, then one to three turns with a wrench.

NPT, NPS, BSPT and BSPP

ThreadTaperAngleSeals byFits NPT?
NPT1:1660°Thread flanks + sealant—
NPTF (Dryseal)1:1660°Thread crests, no sealantYes, with sealant
NPS (straight)None60°Gasket or O-ringLoosely, will not seal
BSPT (R / Rc)1:1655°Thread + sealantNo: 1/2 and 3/4 share 14 TPI and start, then leak
BSPP (G)None55°Bonded washer / O-ringNo
  1. Measure the OD of the male thread with calipers.
  2. Count threads per inch with a gauge or ruler.
  3. Check the taper: a straight thread reads the same OD at both ends.
  4. Match OD and TPI to the table. 14 TPI with an OD of 0.84 in is 1/2 NPT; 14 TPI with 0.825 in is likely 1/2 BSP.

Sources: Wikipedia, "National pipe thread" (NPT sizes, TPI, OD, tap drills).

NPT thread chart questions

What size drill for a 1/4 NPT tap?
7/16 in (0.4375 in) when tapping without a reamer. With a taper pipe reamer, drill 27/64 first.
What tap drill for 1/8 NPT?
Letter R (0.339 in, 8.6 mm). 11/32 (0.3438 in) is the nearest fractional bit.
What drill for 1/2 NPT?
23/32 in (0.7188 in, 18.3 mm).
Why is 1/2 inch pipe 0.84 inches across?
Pipe sizes are named after an old nominal bore, not the outside diameter. The OD stayed fixed when wall thicknesses changed, so the name no longer matches any measurement.
Can I use NPT with BSP fittings?
Not reliably. The thread angle differs (60° vs 55°) and some TPIs differ. 1/2 and 3/4 in share 14 TPI and will start, but they will leak or gall.