Skip to the chart
drillbitsizechart

Tap Drill Chart

The drill to use before tapping every Unified coarse and fine thread, the thread percentage it gives and the clearance holes for the same screw.

Try

1/4-20 UNC · 0.2500 in major · 20 TPI (1.27 mm pitch)

#7tap drill0.2010inch75%thread

Tap drill
#7 0.2010 · 75% thread
Metric drill instead
5.1 mm · 76%
Clearance hole
close F 0.2570 · free H 0.2660
Minor diameter
0.1959 in (basic)

Pick a lower % for hard metal or deep holes; the last column updates.

Tap drill chart, UNC and UNF47 threads, #0 to 1-1/2 in

ThreadSeriesMajor inTap drillThreadDrill for 75%Close fitFree fit
#0-80UNF0.06003/64 0.046981%1.2 mm 79%#52#50
#1-64UNC0.0730#53 0.059567%1.45 mm 78%#48#46
#1-72UNF0.0730#53 0.059575%#53 75%#48#46
#2-56UNC0.0860#50 0.070069%1.75 mm 74%#43#41
#2-64UNF0.0860#50 0.070079%1.8 mm 75%#43#41
#3-48UNC0.0990#47 0.078576%2.0 mm 75%#37#35
#3-56UNF0.0990#45 0.082073%#45 73%#37#35
#4-40UNC0.1120#43 0.089071%2.25 mm 72%#32#30
#4-48UNF0.1120#42 0.093568%2.35 mm 72%#32#30
#5-40UNC0.1250#38 0.101572%2.55 mm 76%#30#29
#5-44UNF0.1250#37 0.104071%2.6 mm 77%#30#29
#6-32UNC0.1380#36 0.106578%2.75 mm 73%#27#25
#6-40UNF0.1380#33 0.113077%2.9 mm 73%#27#25
#8-32UNC0.1640#29 0.136069%3.4 mm 74%#18#16
#8-36UNF0.1640#29 0.136078%3.5 mm 73%#18#16
#10-24UNC0.1900#25 0.149575%#25 75%#9#7
#10-32UNF0.1900#21 0.159076%#21 76%#9#7
#12-24UNC0.2160#16 0.177072%#16 72%#2#1
#12-28UNF0.2160#14 0.182073%4.6 mm 75%#2#1
1/4-20UNC0.2500#7 0.201075%#7 75%FH
1/4-28UNF0.2500#3 0.213080%5.5 mm 72%FH
5/16-18UNC0.3125F 0.257077%F 77%PQ
5/16-24UNF0.3125I 0.272075%I 75%PQ
3/8-16UNC0.37505/16 0.312577%8.0 mm 74%WX
3/8-24UNF0.3750Q 0.332079%8.5 mm 75%WX
7/16-14UNC0.4375U 0.368075%U 75%29/6415/32
7/16-20UNF0.437525/64 0.390672%9.9 mm 73%29/6415/32
1/2-13UNC0.500027/64 0.421978%10.8 mm 75%33/6417/32
1/2-20UNF0.500029/64 0.453172%11.5 mm 73%33/6417/32
9/16-12UNC0.562531/64 0.484472%12.2 mm 76%——
9/16-18UNF0.562533/64 0.515665%12.9 mm 76%——
5/8-11UNC0.625017/32 0.531379%13.6 mm 76%41/6421/32
5/8-18UNF0.625037/64 0.578165%14.5 mm 75%41/6421/32
3/4-10UNC0.750021/32 0.656372%16.5 mm 77%49/6425/32
3/4-16UNF0.750011/16 0.687577%17.5 mm 75%49/6425/32
7/8-9UNC0.875049/64 0.765676%19.5 mm 74%57/6429/32
7/8-14UNF0.875013/16 0.812567%20.5 mm 73%57/6429/32
1-8UNC1.00007/8 0.875077%22.25 mm 76%1-1/641-1/32
1-12UNF1.000059/64 0.921972%59/64 72%1-1/641-1/32
1-1/8-7UNC1.125063/64 0.984476%63/64 76%——
1-1/8-12UNF1.12501-3/64 1.046972%26.5 mm 75%——
1-1/4-7UNC1.25001-7/64 1.109476%28.0 mm 80%——
1-1/4-12UNF1.25001-11/64 1.171972%29.5 mm 82%——
1-3/8-6UNC1.37501-7/32 1.218872%1-7/32 72%——
1-3/8-12UNF1.37501-19/64 1.296972%1-9/32 87%——
1-1/2-6UNC1.50001-11/32 1.343872%1-11/32 72%——
1-1/2-12UNF1.50001-27/64 1.421972%1-13/32 87%——

UNC and UNF tap drill chart

Each row is a Unified thread: nominal size, threads per inch, the series (UNC coarse or UNF fine), the standard tap drill, and the thread engagement that drill gives. The last column is the clearance drill for the same screw, close fit then free fit, so one row answers both "what do I drill to tap this" and "what do I drill for the bolt to pass through".

ThreadSeriesTap drillInchmmThread %Clearance close / free
#0-80UNF3/640.04691.1981%#52 / #50
#1-64UNC#530.05951.5167%#48 / #46
#1-72UNF#530.05951.5175%#48 / #46
#2-56UNC#500.07001.7869%#43 / #41
#2-64UNF#500.07001.7879%#43 / #41
#3-48UNC#470.07851.9976%#37 / #35
#3-56UNF#450.08202.0873%#37 / #35
#4-40UNC#430.08902.2671%#32 / #30
#4-48UNF#420.09352.3768%#32 / #30
#5-40UNC#380.10152.5872%#30 / #29
#5-44UNF#370.10402.6471%#30 / #29
#6-32UNC#360.10652.7178%#27 / #25
#6-40UNF#330.11302.8777%#27 / #25
#8-32UNC#290.13603.4569%#18 / #16
#8-36UNF#290.13603.4578%#18 / #16
#10-24UNC#250.14953.8075%#9 / #7
#10-32UNF#210.15904.0476%#9 / #7
#12-24UNC#160.17704.5072%#2 / #1
#12-28UNF#140.18204.6273%#2 / #1
1/4-20UNC#70.20105.1175%F / H
1/4-28UNF#30.21305.4180%F / H
5/16-18UNCF0.25706.5377%P / Q
5/16-24UNFI0.27206.9175%P / Q
3/8-16UNC5/160.31257.9477%W / X
3/8-24UNFQ0.33208.4379%W / X
7/16-14UNCU0.36809.3575%29/64 / 15/32
7/16-20UNF25/640.39069.9272%29/64 / 15/32
1/2-13UNC27/640.421910.7278%33/64 / 17/32
1/2-20UNF29/640.453111.5172%33/64 / 17/32
9/16-12UNC31/640.484412.3072%—
9/16-18UNF33/640.515613.1065%—
5/8-11UNC17/320.531313.4979%41/64 / 21/32
5/8-18UNF37/640.578114.6865%41/64 / 21/32
3/4-10UNC21/320.656316.6772%49/64 / 25/32
3/4-16UNF11/160.687517.4677%49/64 / 25/32
7/8-9UNC49/640.765619.4576%57/64 / 29/32
7/8-14UNF13/160.812520.6467%57/64 / 29/32
1-8UNC7/80.875022.2377%1-1/64 / 1-1/32
1-12UNF59/640.921923.4272%1-1/64 / 1-1/32
1-1/8-7UNC63/640.984425.0076%—
1-1/8-12UNF1-3/641.046926.5972%—
1-1/4-7UNC1-7/641.109428.1876%—
1-1/4-12UNF1-11/641.171929.7772%—
1-3/8-6UNC1-7/321.218830.9672%—
1-3/8-12UNF1-19/641.296932.9472%—
1-1/2-6UNC1-11/321.343834.1372%—
1-1/2-12UNF1-27/641.421936.1272%—

What thread percentage means

A tap does not cut a full-depth thread. The tap drill leaves some material at the crest, and the percentage says how much of the full thread depth the tap actually cuts. The standard drills above give 60 to 80%. Above 75% the thread gets only slightly stronger, while the torque on the tap rises steeply, which is why 75% is the usual target in mild steel and about 60–65% in stainless, titanium or deep holes.

#7 drill 0.2010 = 75%major0.2500minor0.1959pitch 0.050 in60° thread form · 1/4-20 UNC
A 1/4-20 thread. The tap drill (orange) sits a little above the basic minor diameter; the tap cuts everything from that line to the major diameter.

Thread percentage is 76.98 × (major diameter − drill) ÷ pitch with everything in inches and pitch = 1 ÷ TPI. For 1/4-20 with a #7 drill: 76.98 × (0.250 − 0.201) ÷ 0.05 = 75.4%. The tap drill calculator runs this for any thread and percentage.

Coarse or fine?

UNC (coarse)UNF (fine)
Example1/4-20, 3/8-16, 1/2-131/4-28, 3/8-24, 1/2-20
Best inAluminum, cast iron, plastics, wood insertsSteel, thin walls, adjustment screws
StrengthsFaster to assemble, tolerates dirt and damage, less cross-threadingLarger stress area, finer adjustment, resists loosening under vibration
Tap drillSmaller (deeper thread)Larger (shallower thread)
Tapping by hand? Turn the tap a half turn forward and a quarter turn back to break the chip, and use cutting oil in steel. In blind holes drill deeper than the thread by at least three pitches so chips have somewhere to go.

Sources: Wikipedia, "List of drill and tap sizes" (inch and metric tap drills, clearance holes); Wikipedia, "Unified Thread Standard" (UNC / UNF series, number-screw diameters).

Tap drill chart questions

What size drill for a 1/4-20 tap?
#7 (0.201 in, 5.1 mm), giving about 75% thread. 13/64 (0.2031 in) works if you have no #7, at about 72%.
What drill size for a 10-32 tap?
#21 (0.159 in, 4.04 mm). For 10-24 use #25 (0.1495 in).
What tap drill for 3/8-16?
5/16 (0.3125 in, 7.94 mm), about 77% thread. For 3/8-24 use Q (0.332 in).
What drill for a 1/2-13 tap?
27/64 (0.4219 in, 10.72 mm). For 1/2-20 UNF use 29/64.
What tap drill for 8-32?
#29 (0.136 in, 3.45 mm). 3.5 mm is a close metric substitute, slightly over.
What drill for a 5/16-18 tap?
Letter F (0.257 in, 6.53 mm). For 5/16-24 use letter I (0.272 in).