Skip to the chart
drillbitsizechart

Drill Speed Chart

Starting RPM for high-speed steel bits by size and material, from the surface speed formula. Enter a size to get the RPM for every material.

Try

1/4 (0.2500 in) HSS drill in mild steel

1220–1680RPM80–110surface ft/min24–34m/min

Formula
RPM = 3.82 × SFM ÷ diameter in inches (12 ÷ π = 3.82)
Cobalt or carbide
cobalt about 10–25% faster; carbide often 2–3× in rigid setups
Step drill / hole saw
use the largest diameter in the formula

Drill speed chart, RPM for HSS bitsmiddle of each SFM range, rounded to 10

DrillAluminumBrass and bronzeCast ironMild steelTool steelStainless steelPlasticsHardwood
1/1615280137505190581030602440917024450
3/321019091703460387020401630611016300
1/8764068802600290015301220458012220
5/326110550020802320122098036709780
3/165090458017301940102081030608150
7/32437039301480166087070026206980
1/4382034401300145076061022906110
5/16306027501040116061049018304890
3/82550229087097051041015304070
7/162180196074083044035013103490
1/21910172065073038031011503060
5/8153013805205803102409202440
3/4127011504304802502007602040
7/810909803704102201706501750
19508603203601901505701530

RPM by drill size and material

Spindle speed comes from one formula: RPM = 12 × SFM ÷ (π × diameter in inches), where SFM is the surface speed the material tolerates at the cutting edge. In metric, RPM = 1000 × Vc ÷ (π × diameter in mm) with Vc in metres per minute. The table gives the range for high-speed steel (HSS) bits, rounded to the nearest 10 RPM.

DrillAluminumBrass and bronzeMild steelCast iron (soft)Stainless steelHardwood
1/1612220–183309170–183304890–67204280–61101830–306018330–30560
1/86110–91704580–91702440–33602140–3060920–15309170–15280
3/164070–61103060–61101630–22401430–2040610–10206110–10190
1/43060–45802290–45801220–16801070–1530460–7604580–7640
5/162440–36701830–3670980–1340860–1220370–6103670–6110
3/82040–30601530–3060810–1120710–1020310–5103060–5090
1/21530–22901150–2290610–840530–760230–3802290–3820
5/81220–1830920–1830490–670430–610180–3101830–3060
3/41020–1530760–1530410–560360–510150–2501530–2550
1Infinity–InfinityInfinity–InfinityInfinity–InfinityInfinity–InfinityInfinity–InfinityInfinity–Infinity
01,0002,0003,0004,0001/81/41/23/41drill diameter (in)RPMAluminumMild steelStainless steel
RPM falls with diameter: double the bit and you halve the speed. Curves use the middle of each surface speed range; small bits in aluminum are capped at the top of the chart.

Surface speed by material

Aluminum200–300 SFMBrass and bronze150–300 SFMCast iron (soft)70–100 SFMMild steel80–110 SFMTool steel / alloy steel40–60 SFMStainless steel30–50 SFMPlastics (acrylic, nylon)100–200 SFMHardwood300–500 SFM
The solid bar is the low end of the range, the pale bar the high end. Start at the low end and go up if the chips look good.
Cobalt and carbide: cobalt (M35, M42) bits run about 10–20% faster than HSS in steel; solid carbide runs two to three times faster but needs a rigid machine. Hand drills and most bench drill presses cannot use those speeds anyway, so the HSS numbers are the practical ceiling.

How to tell the speed is wrong

  1. Blue or straw-coloured chips in steel, squealing, or a glazed hole: too fast. Drop the speed by a third.
  2. Long stringy chips that wrap the bit in aluminum or mild steel: feed is too light. Push harder or peck.
  3. Chatter, a triangular hole, or the bit grabbing on breakthrough: too slow a speed with too much feed, or a dull bit. Common with brass and plastics: dub the cutting edge or use a brass-grind bit.
  4. Smoke in hardwood: too slow a feed for the speed, not too fast a speed. Clear chips more often.

Drill press belt settings

Step-pulley drill presses rarely have the exact RPM the table asks for. Choose the nearest step below the number. A typical 12-speed bench press runs roughly 250 to 3,000 RPM; for 1/2 in in mild steel (about 700 RPM by the table) that means a step around 600 to 700. For anything over 3/4 in in steel, the slowest step is usually still too fast; use a step drill, a hole saw or a pilot hole and steady feed.

Sources: Wikipedia, "Drill bit sizes" (number and letter gauge tables, after ASME B94.11M).

Drill speed chart questions

What RPM for a 1/4 inch drill in steel?
About 1220 to 1680 RPM in mild steel with an HSS bit (80–110 SFM). Use about half that in stainless.
What speed should I drill aluminum?
Fast: 200–300 SFM, so a 1/4 in bit runs about 3060 to 4580 RPM. Use cutting fluid or WD-40 to stop aluminum welding to the edge.
Why do big drill bits need slow speeds?
The edge of a bigger bit travels farther per turn. At the same RPM a 1 in bit cuts four times faster at the edge than a 1/4 in bit, and overheats.
What is SFM?
Surface feet per minute: how fast the outer corner of the bit moves across the material. Each material has a safe SFM range; the RPM follows from the bit diameter.
Does stainless steel need slow drilling?
Yes: 30–50 SFM, with steady heavy feed so the edge cuts under the work-hardened skin. Letting the bit rub hardens the surface and makes it worse.