Skip to the chart
drillbitsizechart

Pilot Hole Chart

Pilot and shank hole sizes for every wood screw gauge, hardwood and softwood, with the alternatives other charts give.

Try

#8 wood screw · 0.1640 in shank · hardwood

7/64pilot hole11/64shank clearance0.3320head, in

Pilot (hardwood)
7/64 0.1094 · or number drill #35
Pilot (softwood)
5/64 0.0781
Bigger, common rule of thumb
1/8 — use it in dense hardwood, near an edge, or with brass screws
Shank clearance (top board)
11/64 0.1719 · or #18
Countersink to
0.3320 in (8.4 mm) across the head

Pilot hole chart for wood screws#0 to #24

GaugeShank inHardwood pilotSoftwood pilotShank holeHead in
#00.06003/64 0.04691/32 0.03131/16 0.06250.1190
#10.07303/64 0.04691/32 0.03135/64 0.07810.1460
#20.08601/16 0.06253/64 0.04693/32 0.09380.1720
#30.09901/16 0.06253/64 0.04697/64 0.10940.1990
#40.11205/64 0.07813/64 0.04697/64 0.10940.2250
#50.12505/64 0.07811/16 0.06251/8 0.12500.2520
#60.13803/32 0.09381/16 0.06259/64 0.14060.2790
#70.15103/32 0.09381/16 0.06255/32 0.15630.3050
#80.16407/64 0.10945/64 0.078111/64 0.17190.3320
#90.17701/8 0.12505/64 0.07813/16 0.18750.3580
#100.19001/8 0.12503/32 0.09383/16 0.18750.3850
#110.20301/8 0.12503/32 0.093813/64 0.20310.4120
#120.21609/64 0.14063/32 0.09387/32 0.21880.4380
#140.24205/32 0.15637/64 0.10941/4 0.25000.5070
#160.26803/16 0.18751/8 0.125017/64 0.26560.5440
#180.29403/16 0.18759/64 0.140619/64 0.29690.6350
#200.32007/32 0.21885/32 0.156321/64 0.32810.6500
#240.37201/4 0.250011/64 0.17193/8 0.37500.7620

Wood screw pilot holes

The pilot hole is drilled into the piece the screw threads into, and it is about the size of the screw's root (the solid core between the threads). Hardwood needs a bigger pilot than softwood, because dense wood will not compress around the thread and the screw can snap or split the board. The shank hole goes through the top board so the screw pulls the boards together instead of jacking them apart.

ScrewDiameter inPilot: hardwoodPilot: softwoodShank hole
#00.06003/64 (#58)1/32 (#69)1/16 (#52)
#10.07303/64 (#55)1/32 (#65)5/64 (#47)
#20.08601/16 (#53)3/64 (#59)3/32 (#42)
#30.09901/16 (#51)3/64 (#56)7/64 (#37)
#40.11205/64 (#48)3/64 (#55)7/64 (#32)
#50.12505/64 (#44)1/16 (#53)1/8 (#30)
#60.13803/32 (#42)1/16 (#52)9/64 (#27)
#70.15103/32 (#38)1/16 (#50)5/32 (#22)
#80.16407/64 (#35)5/64 (#48)11/64 (#18)
#90.17701/8 (#32)5/64 (#46)3/16 (#14)
#100.19001/8 (#30)3/32 (#44)3/16 (#10)
#110.20301/8 (#29)3/32 (#43)13/64 (#4)
#120.21609/64 (#27)3/32 (#39)7/32 (#2)
#140.24205/32 (#20)7/64 (#34)1/4 (D)
#160.26803/16 (#16)1/8 (#31)17/64 (I)
#180.29403/16 (#10)9/64 (#29)19/64 (N)
#200.32007/32 (#3)5/32 (#26)21/64 (P)
#240.37201/4 (D)11/64 (#18)3/8 (V)

Number-drill equivalents are in brackets for anyone with a number set; any bit within a few thousandths works.

shank hole 11/64 inpilot hole 7/64 in (hardwood)top board (clamped)bottom board (threads bite here)
The shank hole in the top board is the full screw size, so the thread bites only the bottom board and pulls the joint tight.

Why charts disagree

Pilot sizes are not standardised. The table above follows Engineering ToolBox; many woodworking charts and screw makers go a size larger for the common gauges:

ScrewThis chart hard / softCommon alternative hard / soft
#63/32 / 1/167/64 / 3/32
#87/64 / 5/641/8 / 7/64
#101/8 / 3/329/64 / 1/8

Both work. Use the larger pilot in oak, maple and other hardwoods near the end of a board, and the smaller one in pine, plywood and when the screw needs maximum holding power. Make a test hole in scrap: the screw should drive firmly without the head stalling or the wood cracking.

Countersinks, plugs and brass

  1. For flat-head screws, countersink to the head diameter: a #8 head is 0.3320 in across. A combination pilot/countersink bit does pilot, shank and countersink in one pass.
  2. For plugs, counterbore 3/8 in for #6 to #10 screws and cut plugs with a 3/8 in plug cutter.
  3. Brass and stainless screws are softer or more brittle than steel: drill the hardwood pilot even in softwood, and drive a steel screw first to cut the thread.
  4. Within 1 in of the end grain, go one size larger on the pilot to stop splits.

Sources: Engineering ToolBox, "US Wood Screws – Pilot Holes".

Pilot hole chart questions

What size pilot hole for a #8 wood screw?
7/64 in in hardwood, 5/64 in in softwood, with an 11/64 in shank hole through the top board. Some charts give 1/8 and 7/64.
What size pilot hole for a #10 screw?
1/8 in in hardwood, 3/32 in in softwood. Shank hole 3/16 in.
What pilot hole for a #6 screw?
3/32 in in hardwood, 1/16 in in softwood. Shank hole 9/64 in.
Do I need a pilot hole for wood screws?
In hardwood, always. In softwood, for screws #8 and up or within an inch of an edge. Self-drilling construction screws are designed to go in without one.
What is the difference between a pilot hole and a shank hole?
The pilot is drilled in the part the screw threads into, about the size of the screw root. The shank hole is drilled through the top part at full screw size, so the screw clamps rather than threads into it.