Skip to the chart
drillbitsizechart

Letter Drill Size Chart

All 26 letter drills from A (0.234 in) to Z (0.413 in), with millimetres, tap drill and clearance uses, drawn to scale against fractional and metric bits.

Try

F → letter drill F

0.2570inch6.528mm≈ 1/4nearest 64th, −0.0070

FracFractional

1/4 0.2500

−0.0070 in · −0.178 mm · undersize

next over: 17/64 0.2656

No.Number

#1 0.2280

−0.0290 in · −0.737 mm · undersize

largest number drill

LtrLetter

F 0.2570

exact match

mmMetric

6.5 mm 0.2559

−0.0011 in · −0.028 mm · undersize

next over: 6.6 mm 0.2598

This size is the tap drill for 5/16-18 UNC · close-fit clearance for a 1/4 screw

Letter drill sizes26 sizes, smallest first

SizeDecimal inmmNearest 64th
A0.23405.944≈ 15/64
B0.23806.045≈ 15/64
C0.24206.147≈ 15/64
D0.24606.248≈ 1/4
E0.25006.35= 1/4
F0.25706.528≈ 1/4
G0.26106.629≈ 17/64
H0.26606.756≈ 17/64
I0.27206.909≈ 17/64
J0.27707.036≈ 9/32
K0.28107.137≈ 9/32
L0.29007.366≈ 19/64
M0.29507.493≈ 19/64
N0.30207.671≈ 19/64
O0.31608.026≈ 5/16
P0.32308.204≈ 21/64
Q0.33208.433≈ 21/64
R0.33908.611≈ 11/32
S0.34808.839≈ 11/32
T0.35809.093≈ 23/64
U0.36809.347≈ 3/8
V0.37709.576≈ 3/8
W0.38609.804≈ 25/64
X0.397010.084≈ 25/64
Y0.404010.262≈ 13/32
Z0.413010.49≈ 13/32

The A to Z series

Letter drills pick up where number drills stop. A is 0.2340 in, just above #1 (0.2280 in), and Z is 0.4130 in (10.49 mm), a little over 13/32. Unlike number drills, letters run the normal way round: later letters are bigger. The steps are between 0.004 and 0.014 in, mostly finer than the 1/64 (0.0156 in) steps of fractional bits.

0.230.240.250.260.270.280.290.300.310.320.330.340.350.360.370.380.390.400.41inchLetterAFIQUZFractional1/45/163/8Metric
Letter drills (dotted lane) span 0.234 to 0.413 in. F, the 5/16-18 tap drill and 1/4 in close-fit clearance, is circled.

Every letter size and what it is for

LetterInchmmTap drill / clearance
A0.23405.94—
B0.23806.05—
C0.24206.15—
D0.24606.25—
E0.25006.35—
F0.25706.53tap 5/16-18, 1/4 close clearance
G0.26106.63—
H0.26606.761/4 free clearance
I0.27206.91tap 5/16-24
J0.27707.04—
K0.28107.14—
L0.29007.37—
M0.29507.49—
N0.30207.67—
O0.31608.03—
P0.32308.205/16 close clearance
Q0.33208.43tap 3/8-24, 5/16 free clearance
R0.33908.61—
S0.34808.84—
T0.35809.09—
U0.36809.35tap 7/16-14
V0.37709.58—
W0.38609.803/8 close clearance
X0.397010.083/8 free clearance
Y0.404010.26—
Z0.413010.49—

Why F, I, Q and U matter

Four letters do most of the work. F (0.257 in) is the 5/16-18 tap drill and the close-fit hole for a 1/4 in bolt. I (0.272 in) taps 5/16-24. Q (0.332 in) taps 3/8-24 and is the free-fit hole for a 5/16 bolt. U (0.368 in) taps 7/16-14. If you only buy four letter bits, buy those.

F0.2570 inI0.2720 inQ0.3320 inU0.3680 in
The four letter drills used most often, drawn to the same scale.

Letter drills for reamer pre-drilling

A machine reamer wants roughly 0.008 to 0.015 in of stock on the diameter for sizes from 1/4 to 1/2 in. Letter drills give that allowance where fractional bits cannot: for a 1/4 in reamer, drill B (0.238 in, 0.012 in of stock) or C (0.242 in, 0.008 in); for a 5/16 in reamer, drill N (0.302 in, 0.0105 in); for a 3/8 in reamer, drill U (0.368 in, 0.007 in) or 23/64 (0.3594 in). E (0.250 in) is the same size as 1/4 and leaves nothing to ream. Check your reamer maker's allowance; these are starting points.

Sources: Wikipedia, "Drill bit sizes" (number and letter gauge tables, after ASME B94.11M); Wikipedia, "List of drill and tap sizes" (inch and metric tap drills, clearance holes).

Letter drill sizes questions

What size is a letter F drill bit?
F is 0.2570 in (6.528 mm). It is the tap drill for 5/16-18 and the close-fit clearance hole for a 1/4 in screw. A 6.5 mm bit is the nearest metric substitute.
What is the smallest letter drill?
A, at 0.2340 in (5.944 mm). It follows #1 (0.228 in), the largest number drill.
What letter drill is 5/16?
None exactly. 5/16 in is 0.3125 in, between N (0.302 in) and O (0.316 in). O is 0.0035 in over.
What letter drill do I need for a 3/8-24 tap?
Q, 0.3320 in (8.433 mm). 8.4 mm is the closest metric bit.
Is letter E the same as 1/4 inch?
Yes, to the thousandth: E is listed as 0.2500 in, the same as a 1/4 fractional bit. Sets include both for completeness.