Skip to the chart
drillbitsizechart

Screw Size Chart

What #4, #8 or #10 actually measures: diameter in inches and millimetres, coarse and fine threads, and how to name an unknown screw.

Try

Measured 0.1900 in (4.83 mm) across the threads

#10 machine screwbest match±0.0000in, nominal minus yoursM5runner-up

#10 machine screw
0.1900 in nominal · ±0.00 mm · 24 TPI (UNC) or 32 TPI (UNF)
M5
0.1969 in nominal · +0.17 mm · 0.8 mm pitch
#8 machine screw
0.1640 in nominal · −0.66 mm · 32 TPI (UNC) or 36 TPI (UNF)
Tell them apart
real threads measure 0.002–0.010 in under nominal. Count threads over 1/2 in (or use a pitch gauge) to split inch from metric

Screw size chart, inch and metricsorted by diameter

SizeInchmmThreads
#00.06001.5280 UNF
M1.60.06301.60.35 mm
#10.07301.8564 UNC, 72 UNF
M20.078720.4 mm
#20.08602.1856 UNC, 64 UNF
M2.50.09842.50.45 mm
#30.09902.5148 UNC, 56 UNF
#40.11202.8440 UNC, 48 UNF
M30.118130.5 mm
#50.12503.1740 UNC, 44 UNF
#60.13803.5132 UNC, 40 UNF
M40.157540.7 mm
#80.16404.1732 UNC, 36 UNF
#100.19004.8324 UNC, 32 UNF
M50.196950.8 mm
#120.21605.4924 UNC, 28 UNF
M60.236261 mm
1/4 in0.25006.3520 UNC, 28 UNF
5/16 in0.31257.9418 UNC, 24 UNF
M80.315081.25 mm, 1 mm
3/8 in0.37509.5216 UNC, 24 UNF
M100.3937101.5 mm, 1.25 mm, 1 mm
7/16 in0.437511.1114 UNC, 20 UNF
M120.4724121.75 mm, 1.5 mm, 1.25 mm
1/2 in0.500012.713 UNC, 20 UNF
M140.5512142 mm, 1.5 mm
9/16 in0.562514.2912 UNC, 18 UNF
5/8 in0.625015.8811 UNC, 18 UNF
M160.6299162 mm, 1.5 mm
3/4 in0.750019.0510 UNC, 16 UNF
M200.7874202.5 mm, 1.5 mm
7/8 in0.875022.229 UNC, 14 UNF
M240.9449243 mm, 2 mm
1 in1.000025.48 UNC, 12 UNF
1-1/8 in1.125028.577 UNC, 12 UNF
M301.1811303.5 mm
1-1/4 in1.250031.757 UNC, 12 UNF
1-3/8 in1.375034.926 UNC, 12 UNF
1-1/2 in1.500038.16 UNC, 12 UNF

Screw gauge to diameter

A screw's number is a gauge, not a measurement. The diameter in inches is 0.060 + 0.013 × gauge, so a #10 screw is 0.060 + 0.130 = 0.190 in. The same numbers are used for machine screws and wood screws; only the threads differ. Above #12 inch screws are sold by fraction (1/4, 5/16), and metric screws by M-number, which is simply the diameter in millimetres.

GaugeDiameter inmmCoarse (UNC)Fine (UNF)Wood screw head
#00.06001.52—#0-800.1190
#10.07301.85#1-64#1-720.1460
#20.08602.18#2-56#2-640.1720
#30.09902.51#3-48#3-560.1990
#40.11202.84#4-40#4-480.2250
#50.12503.18#5-40#5-440.2520
#60.13803.51#6-32#6-400.2790
#80.16404.17#8-32#8-360.3320
#100.19004.83#10-24#10-320.3850
#120.21605.49#12-24#12-280.4380

Wood screws continue past #12 in even gauges:

GaugeDiameter inmmHead dia in
#70.15103.840.3050
#90.17704.500.3580
#110.20305.160.4120
#140.24206.150.5070
#160.26806.810.5440
#180.29407.470.6350
#200.32008.130.6500
#240.37209.450.7620
#00.0600 in · 1.52 mm#10.0730 in · 1.85 mm#20.0860 in · 2.18 mm#30.0990 in · 2.51 mm#40.1120 in · 2.84 mm#50.1250 in · 3.18 mm#60.1380 in · 3.51 mm#80.1640 in · 4.17 mm#100.1900 in · 4.83 mm#120.2160 in · 5.49 mm#140.2420 in · 6.15 mm#160.2680 in · 6.81 mm#180.2940 in · 7.47 mm#200.3200 in · 8.13 mm#240.3720 in · 9.45 mm
Each gauge step adds 0.013 in (0.33 mm). Blue gauges exist as machine screws too; grey ones are wood screws only.

Reading a screw label

LabelGaugeThreadLengthNotes
#8-32 × 1/2#8 (0.164 in)32 per inch, UNC1/2 inMachine screw
#10-32 × 3/4#10 (0.190 in)32 per inch, UNF3/4 inCommon in electronics and bikes
#8 × 1-1/4#8Wood thread1-1/4 inNo TPI given: a wood or sheet metal screw
1/4-20 × 11/4 in20 per inch1 inAbove #12 the size is a fraction
M4 × 0.7 × 104 mm0.7 mm pitch10 mmMetric
Length is measured from under the head to the tip, except for flat (countersunk) heads, which are measured overall, because the head ends up flush with the surface.

Which size do I have?

  1. Measure the thread diameter across the crests with calipers.
  2. Subtract 0.060 and divide by 0.013 for the gauge: 0.162 in reads as (0.162 − 0.060) ÷ 0.013 ≈ 7.8, so #8.
  3. If the reading is a round number of millimetres (3.0, 4.0, 5.0) it is probably metric: an M4 is 0.157 in, between #6 and #8.
  4. Count threads per inch to tell #10-24 from #10-32, then look up the tap drill or clearance hole.

Sources: Wikipedia, "Unified Thread Standard" (UNC / UNF series, number-screw diameters); Engineering ToolBox, "US Wood Screws – Pilot Holes".

Screw size chart questions

What is the diameter of a #10 screw?
0.190 in (4.83 mm). The formula is 0.060 + 0.013 × 10.
How big is a #8 screw in mm?
0.164 in, which is 4.17 mm. The nearest metric screw is M4 (4.0 mm), but the threads are not interchangeable.
What does 8-32 mean on a screw?
Gauge #8 (0.164 in diameter) with 32 threads per inch.
Is a #10 screw the same as 3/16?
Nearly: #10 is 0.190 in and 3/16 is 0.1875 in. Screws are sold as #10, so a 3/16 drill is a common shank hole for #10 wood screws.
What size is a #6 screw?
0.138 in (3.51 mm). Machine screws come as #6-32 (coarse) or #6-40 (fine).