64ths, 32nds, 16ths
Fractional bits are sold in 1/64 in steps up to 1 in, then in coarser steps; this chart lists 88 sizes from 1/64 to 2 in. Every fraction is shown in lowest terms, so 8/64 is 1/8 and 24/64 is 3/8. The odd 64ths (5/64, 7/64, 9/64 …) are what separate a 29-piece set from a 21-piece or 13-piece set.
Which set do I need?
| Set | Sizes | Steps | Good for |
|---|---|---|---|
| 13 piece | 1/16 to 1/4 | 1/64 | Pilot holes, small hardware |
| 21 piece | 1/16 to 3/8 | 1/64 | General shop and home use |
| 29 piece | 1/16 to 1/2 | 1/64 | Machining, tap drills up to 1/2-13 (27/64) |
| Silver and Deming | 9/16 to 1 | 1/16 | Large holes with a 1/2 in reduced shank |
The 29-piece set covers every fractional tap drill in the standard table up to 1/2-13 (27/64) and 1/2-20 (29/64). Above 1/2 in, bits usually come with a 1/2 in reduced shank so they fit a 1/2 in chuck, so check your chuck before buying the large sizes.
Fractional bits to 1/2 inch with substitutes
| Fraction | Inch | mm | Nearest metric | Nearest number / letter |
|---|---|---|---|---|
| 1/64 | 0.0156 | 0.40 | 0.4 mm +0.0001 | #78 +0.0004 |
| 1/32 | 0.0313 | 0.79 | 0.8 mm +0.0002 | #68 −0.0003 |
| 3/64 | 0.0469 | 1.19 | 1.2 mm +0.0004 | #56 −0.0004 |
| 1/16 | 0.0625 | 1.59 | 1.6 mm +0.0005 | #52 +0.0010 |
| 5/64 | 0.0781 | 1.98 | 2.0 mm +0.0006 | #47 +0.0004 |
| 3/32 | 0.0938 | 2.38 | 2.4 mm +0.0007 | #42 −0.0003 |
| 7/64 | 0.1094 | 2.78 | 2.8 mm +0.0009 | #35 +0.0006 |
| 1/8 | 0.1250 | 3.18 | 3.2 mm +0.0010 | #30 +0.0035 |
| 9/64 | 0.1406 | 3.57 | 3.6 mm +0.0011 | #28 −0.0001 |
| 5/32 | 0.1563 | 3.97 | 4.0 mm +0.0012 | #22 +0.0008 |
| 11/64 | 0.1719 | 4.37 | 4.4 mm +0.0014 | #17 +0.0011 |
| 3/16 | 0.1875 | 4.76 | 4.8 mm +0.0015 | #12 +0.0015 |
| 13/64 | 0.2031 | 5.16 | 5.2 mm +0.0016 | #6 +0.0009 |
| 7/32 | 0.2188 | 5.56 | 5.6 mm +0.0017 | #2 +0.0023 |
| 15/64 | 0.2344 | 5.95 | 6.0 mm +0.0018 | A −0.0004 |
| 1/4 | 0.2500 | 6.35 | 6.3 mm −0.0020 | E +0.0000 |
| 17/64 | 0.2656 | 6.75 | 6.7 mm −0.0018 | H +0.0004 |
| 9/32 | 0.2813 | 7.14 | 7.1 mm −0.0017 | K −0.0002 |
| 19/64 | 0.2969 | 7.54 | 7.5 mm −0.0016 | M −0.0019 |
| 5/16 | 0.3125 | 7.94 | 7.9 mm −0.0015 | O +0.0035 |
| 21/64 | 0.3281 | 8.33 | 8.3 mm −0.0014 | Q +0.0039 |
| 11/32 | 0.3438 | 8.73 | 8.7 mm −0.0012 | S +0.0042 |
| 23/64 | 0.3594 | 9.13 | 9.1 mm −0.0011 | T −0.0014 |
| 3/8 | 0.3750 | 9.52 | 9.5 mm −0.0010 | V +0.0020 |
| 25/64 | 0.3906 | 9.92 | 9.9 mm −0.0009 | W −0.0046 |
| 13/32 | 0.4063 | 10.32 | 10.3 mm −0.0007 | Y −0.0022 |
| 27/64 | 0.4219 | 10.72 | 10.7 mm −0.0006 | — |
| 7/16 | 0.4375 | 11.11 | 11.1 mm −0.0005 | — |
| 29/64 | 0.4531 | 11.51 | 11.5 mm −0.0004 | — |
| 15/32 | 0.4688 | 11.91 | 11.9 mm −0.0002 | — |
| 31/64 | 0.4844 | 12.30 | 12.3 mm −0.0001 | — |
| 1/2 | 0.5000 | 12.70 | 12.7 mm +0.0000 | — |
Reading fractions without a ruler
To get a 64th as a decimal, divide by 64; or remember that 1/64 is 0.015625 and count up. 17/64 is one 64th over 1/4 (0.25 + 0.0156 = 0.2656). The fraction to decimal chart lists every 64th, and the decimal to fraction chart finds the nearest fraction for any decimal with the error.
Sources: Wikipedia, "Drill bit sizes" (number and letter gauge tables, after ASME B94.11M).