How number drill sizes work
Number drills run backwards: the bigger the number, the smaller the bit. #1 is the largest at 0.2280 in (5.79 mm) and #80 is 0.0135 in (0.34 mm). The micro sizes #81 to #97 continue down to 0.0059 in, below the thickness of a sheet of paper. The series grew out of the old Stubs steel wire gauge, which is why the steps are uneven: as little as 0.0004 in apart at the small end and up to 0.0085 in at the large end.
Because they fill the gaps between 64ths, number drills are the standard tap drills and clearance drills for the small machine screws, #0 through #12. A 60-piece index (#1 to #60) covers almost every job; the 61 to 80 set is for instrument work, model making and printed circuit boards.
Number drills you will actually use
These are the number sizes that appear in the standard tap drill and clearance tables. The rest of the series is used for reamer pre-drills and odd fits.
| Drill | Inch | mm | Used for |
|---|---|---|---|
| #1 | 0.2280 | 5.79 | #12 free clearance |
| #2 | 0.2210 | 5.61 | #12 close clearance |
| #3 | 0.2130 | 5.41 | tap 1/4-28 |
| #7 | 0.2010 | 5.11 | tap 1/4-20, #10 free clearance |
| #9 | 0.1960 | 4.98 | #10 close clearance |
| #14 | 0.1820 | 4.62 | tap #12-28 |
| #16 | 0.1770 | 4.50 | tap #12-24, #8 free clearance |
| #18 | 0.1695 | 4.31 | #8 close clearance |
| #21 | 0.1590 | 4.04 | tap #10-32 |
| #25 | 0.1495 | 3.80 | tap #10-24, #6 free clearance |
| #27 | 0.1440 | 3.66 | #6 close clearance |
| #29 | 0.1360 | 3.45 | tap #8-32, tap #8-36, #5 free clearance |
| #30 | 0.1285 | 3.26 | #4 free clearance, #5 close clearance |
| #32 | 0.1160 | 2.95 | #4 close clearance |
| #33 | 0.1130 | 2.87 | tap #6-40 |
| #35 | 0.1100 | 2.79 | #3 free clearance |
| #36 | 0.1065 | 2.71 | tap #6-32 |
| #37 | 0.1040 | 2.64 | tap #5-44, #3 close clearance |
| #38 | 0.1015 | 2.58 | tap #5-40 |
| #41 | 0.0960 | 2.44 | #2 free clearance |
| #42 | 0.0935 | 2.37 | tap #4-48 |
| #43 | 0.0890 | 2.26 | tap #4-40, #2 close clearance |
| #45 | 0.0820 | 2.08 | tap #3-56 |
| #46 | 0.0810 | 2.06 | #1 free clearance |
| #47 | 0.0785 | 1.99 | tap #3-48 |
| #48 | 0.0760 | 1.93 | #1 close clearance |
| #50 | 0.0700 | 1.78 | tap #2-56, tap #2-64, #0 free clearance |
| #52 | 0.0635 | 1.61 | #0 close clearance |
| #53 | 0.0595 | 1.51 | tap #1-64, tap #1-72 |
Metric and fractional substitutes
If the number bit is not in the drawer, a metric bit is usually closer than a fractional one, because metric bits come in 0.1 mm steps (about 0.004 in). The table gives the nearest of each for the sizes people look up most; the difference is in inches, and + means the substitute is bigger.
| Number | Inch | Nearest metric | Nearest fractional |
|---|---|---|---|
| #50 | 0.0700 | 1.8 mm +0.0009 | 1/16 −0.0075 |
| #43 | 0.0890 | 2.25 mm −0.0004 | 3/32 +0.0048 |
| #36 | 0.1065 | 2.7 mm −0.0002 | 7/64 +0.0029 |
| #33 | 0.1130 | 2.85 mm −0.0008 | 7/64 −0.0036 |
| #29 | 0.1360 | 3.5 mm +0.0018 | 9/64 +0.0046 |
| #25 | 0.1495 | 3.8 mm +0.0001 | 5/32 +0.0068 |
| #21 | 0.1590 | 4.0 mm −0.0015 | 5/32 −0.0028 |
| #16 | 0.1770 | 4.5 mm +0.0002 | 11/64 −0.0051 |
| #7 | 0.2010 | 5.1 mm −0.0002 | 13/64 +0.0021 |
| #3 | 0.2130 | 5.4 mm −0.0004 | 7/32 +0.0058 |
Reading a worn bit
Number drills are often stamped on the shank, and the stamp wears off. Measure across the shank (not the flutes) with a micrometer or calipers, type the reading into the search box above, and the chart names the nearest number size and how far off it is. Measure in two directions: a bent or worn shank reads small one way.
Sources: Wikipedia, "Drill bit sizes" (number and letter gauge tables, after ASME B94.11M).