Skip to the chart
drillbitsizechart

Sheet Metal Gauge Chart

Gauge to thickness for the four metals that use different gauge systems. Pick the metal, then type a gauge or a measured thickness.

Try

18 gauge standard steel

0.0478inch1.21mm3/64≈ fraction

Same gauge, other metals
Galvanized steel 0.0516 · Stainless steel 0.0500 · Aluminum 0.0403
Weight
2 lb per sq ft
Drill for a pop rivet hole
see the rivet maker; the sheet only sets grip length

Sheet metal gauge chartinch, mm in grey

GaugeSteelGalvanizedStainlessAluminum
30.2391 6.07—0.2500 6.350.2294 5.83
40.2242 5.69—0.2344 5.950.2043 5.19
50.2092 5.31—0.2188 5.560.1819 4.62
60.1943 4.94—0.2031 5.160.1620 4.11
70.1793 4.55—0.1875 4.760.1443 3.67
80.1644 4.180.1681 4.270.1719 4.370.1285 3.26
90.1495 3.80.1532 3.890.1563 3.970.1144 2.91
100.1345 3.420.1382 3.510.1406 3.570.1019 2.59
110.1196 3.040.1233 3.130.1250 3.170.0907 2.3
120.1046 2.660.1084 2.750.1094 2.780.0808 2.05
130.0897 2.280.0934 2.370.0938 2.380.0720 1.83
140.0747 1.90.0785 1.990.0781 1.980.0641 1.63
150.0673 1.710.0710 1.80.0703 1.790.0571 1.45
160.0598 1.520.0635 1.610.0625 1.590.0508 1.29
170.0538 1.370.0575 1.460.0563 1.430.0453 1.15
180.0478 1.210.0516 1.310.0500 1.270.0403 1.02
190.0418 1.060.0456 1.160.0437 1.110.0359 0.91
200.0359 0.910.0396 1.010.0375 0.950.0320 0.81
210.0329 0.840.0366 0.930.0344 0.870.0285 0.72
220.0299 0.760.0336 0.850.0313 0.80.0253 0.64
230.0269 0.680.0306 0.780.0281 0.710.0226 0.57
240.0239 0.610.0276 0.70.0250 0.640.0201 0.51
250.0209 0.530.0247 0.630.0219 0.560.0179 0.45
260.0179 0.450.0217 0.550.0187 0.470.0159 0.4
270.0164 0.420.0202 0.510.0172 0.440.0142 0.36
280.0149 0.380.0187 0.470.0156 0.40.0126 0.32
290.0135 0.340.0172 0.440.0141 0.360.0113 0.29
300.0120 0.30.0157 0.40.0125 0.320.0100 0.25

One gauge, four thicknesses

A gauge number is not a thickness on its own. 16 gauge steel is 0.0598 in, 16 gauge galvanized is 0.0635 in, 16 gauge stainless is 0.0625 in and 16 gauge aluminum is 0.0508 in. Choose the metal in the box above before reading the chart, or type a measured thickness to find its gauge.

GaugeSteelGalvanizedStainlessAluminum
100.1345 3.420.1382 3.510.1406 3.570.1019 2.59
120.1046 2.660.1084 2.750.1094 2.780.0808 2.05
140.0747 1.900.0785 1.990.0781 1.980.0641 1.63
160.0598 1.520.0635 1.610.0625 1.590.0508 1.29
180.0478 1.210.0516 1.310.0500 1.270.0403 1.02
200.0359 0.910.0396 1.010.0375 0.950.0320 0.81
220.0299 0.760.0336 0.850.0313 0.800.0253 0.64
240.0239 0.610.0276 0.700.0250 0.640.0201 0.51
260.0179 0.450.0217 0.550.0187 0.470.0159 0.40
Steel0.0598 in · 1.52 mmGalvanized0.0635 in · 1.61 mmStainless0.0625 in · 1.59 mmAluminum0.0508 in · 1.29 mm
Aluminum is about 15% thinner than steel at the same gauge, because it uses the older Brown & Sharpe (wire gauge) scale.

Why the systems differ

MaterialGauge systemBased on
Carbon steelManufacturers’ Standard GaugeWeight per square foot: 41.82 lb/ft² per inch of thickness
Galvanized steelGalvanized Sheet GaugeSteel gauge plus the zinc coating, about 0.0037 in
Stainless steelStainless gauge (US)Close to the old US Standard, often a round fraction
Aluminum, brass, copperBrown & Sharpe / AWGThe wire gauge; each step is 0.8905 × the last

Bigger gauge number means thinner sheet, in every system. In Europe and most of the world, sheet is sold by thickness in millimetres (1.0, 1.2, 1.5 mm), so a gauge figure is only needed when reading US drawings.

Drilling sheet metal

  1. Clamp the sheet to a wood backer; a thin sheet grabbed by the bit spins dangerously.
  2. Use a step drill or a bit with a flat (brad) point for holes over 1/4 in in sheet thinner than 18 gauge, so the hole stays round.
  3. Drill clearance holes one size larger than in thick stock: burrs and paint narrow the hole.
  4. For tapped holes in thin sheet, use a high thread percentage or a rivet nut: one thread pitch of 1/4-20 is 0.05 in, about 18 gauge.

Sources: Wikipedia, "Sheet metal" (gauge tables and the weight-per-area basis of the steel gauge); Wikipedia, "American wire gauge" (the Brown & Sharpe formula used for aluminum sheet).

Sheet metal gauge chart questions

How thick is 16 gauge sheet metal?
Steel: 0.0598 in (1.52 mm). Aluminum: 0.0508 in. Stainless: 0.0625 in.
Which is thicker, 18 or 20 gauge?
18 gauge. Lower gauge numbers are thicker: 18 gauge steel is 0.0478 in, 20 gauge is 0.0359 in.
How thick is 14 gauge steel in mm?
0.0747 in, which is 1.90 mm.
Is aluminum gauge the same as steel gauge?
No. Aluminum uses the Brown & Sharpe scale and is thinner at the same number: 16 ga aluminum is 0.0508 in against 0.0598 in for steel.
What gauge is 1 mm sheet?
About 19 to 20 gauge steel (0.0418 and 0.0359 in; 1 mm is 0.0394 in).