Skip to the chart
drillbitsizechart

Metric Tap Drill Chart

ISO tap drills for every coarse and common fine metric thread, with the inch equivalent and the closest inch bit if you have no metric set.

Try

M6 x 1 metric coarse · 6 mm major · 1 mm pitch (25.4 TPI)

5mm tap drill0.1969inch77%thread

Tap drill
5 mm · 77% thread (D − P rule)
Inch drill instead
#9 0.1960 · 79%
Clearance hole
fine 6.4 · medium 6.6 · coarse 7 mm
Minor diameter
4.917 mm (basic)
Pitch diameter
5.35 mm (basic)

The D − P rule gives about 77%; pick 65% or 60% for stainless and titanium.

Metric tap drill chart, ISO coarse and fine33 threads, M1 to M30

ThreadSeriesPitchTap drill mmInchThreadDrill for 75%Clearance mm
M1 x 0.25coarse0.250.750.029577%0.75 mm 77%—
M1.2 x 0.25coarse0.250.950.037477%0.95 mm 77%—
M1.4 x 0.3coarse0.31.10.043377%1.1 mm 77%—
M1.6 x 0.35coarse0.351.250.049277%1.25 mm 77%1.8
M2 x 0.4coarse0.41.60.063077%#52 74%2.4
M2.5 x 0.45coarse0.452.050.080777%#46 76%2.9
M3 x 0.5coarse0.52.50.098477%2.5 mm 77%3.4
M3.5 x 0.6coarse0.62.90.114277%2.9 mm 77%—
M4 x 0.7coarse0.73.30.129977%3.3 mm 77%4.5
M5 x 0.8coarse0.84.20.165477%#19 75%5.5
M6 x 1coarse150.196977%5.0 mm 77%6.6
M8 x 1.25coarse1.256.80.267774%6.8 mm 74%9
M8 x 1fine170.275677%J 74%9
M10 x 1.5coarse1.58.50.334677%8.5 mm 77%11
M10 x 1.25fine1.258.80.346574%8.8 mm 74%11
M10 x 1fine190.354377%9.0 mm 77%11
M12 x 1.75coarse1.7510.20.401679%10.3 mm 75%13.5
M12 x 1.5fine1.510.50.413477%10.5 mm 77%13.5
M12 x 1.25fine1.2510.80.425274%10.8 mm 74%13.5
M14 x 2coarse2120.472477%12.1 mm 73%15.5
M14 x 1.5fine1.512.50.492177%12.5 mm 77%15.5
M16 x 2coarse2140.551277%14.0 mm 77%17.5
M16 x 1.5fine1.514.50.570977%14.5 mm 77%17.5
M18 x 2.5coarse2.515.50.610277%15.5 mm 77%—
M18 x 1.5fine1.516.50.649677%16.5 mm 77%—
M20 x 2.5coarse2.517.50.689077%17.5 mm 77%22
M20 x 1.5fine1.518.50.728377%18.5 mm 77%22
M22 x 2.5coarse2.519.50.767777%19.5 mm 77%—
M22 x 1.5fine1.520.50.807177%20.5 mm 77%—
M24 x 3coarse3210.826877%53/64 76%26
M24 x 2fine2220.866177%22.0 mm 77%26
M27 x 3coarse3240.944977%24.0 mm 77%—
M30 x 3.5coarse3.526.51.043377%26.5 mm 77%33

Metric coarse and fine tap drills

The ISO tap drill for a metric thread is close to the thread diameter minus the pitch. That rule gives about 77% thread, and the recommended drill is that number rounded to a size you can buy. Fine threads have smaller pitches, so their tap drills are larger.

ThreadSeriesTap drill mmInchThread %Nearest inch bit
M1 × 0.25coarse0.750.029577%#69
M1.2 × 0.25coarse0.950.037477%#63
M1.4 × 0.3coarse1.100.043377%#57
M1.6 × 0.35coarse1.250.049277%3/64
M2 × 0.4coarse1.600.063077%1/16
M2.5 × 0.45coarse2.050.080777%#46
M3 × 0.5coarse2.500.098477%#40
M3.5 × 0.6coarse2.900.114277%#33
M4 × 0.7coarse3.300.129977%#30
M5 × 0.8coarse4.200.165477%#19
M6 × 1coarse5.000.196977%#9
M8 × 1.25coarse6.800.267774%H
M8 × 1fine7.000.275677%J
M10 × 1.5coarse8.500.334677%Q
M10 × 1.25fine8.800.346574%S
M10 × 1fine9.000.354377%T
M12 × 1.75coarse10.200.401679%Y
M12 × 1.5fine10.500.413477%13/32
M12 × 1.25fine10.800.425274%27/64
M14 × 2coarse12.000.472477%15/32
M14 × 1.5fine12.500.492177%31/64
M16 × 2coarse14.000.551277%35/64
M16 × 1.5fine14.500.570977%37/64
M18 × 2.5coarse15.500.610277%39/64
M18 × 1.5fine16.500.649677%21/32
M20 × 2.5coarse17.500.689077%11/16
M20 × 1.5fine18.500.728377%47/64
M22 × 2.5coarse19.500.767777%49/64
M22 × 1.5fine20.500.807177%13/16
M24 × 3coarse21.000.826877%53/64
M24 × 2fine22.000.866177%55/64
M27 × 3coarse24.000.944977%15/16
M30 × 3.5coarse26.501.043377%1-1/32

The minus-the-pitch rule

  1. Read the size: M10 × 1.5 means 10 mm major diameter, 1.5 mm pitch.
  2. Subtract the pitch: 10 − 1.5 = 8.5.
  3. Drill 8.5 mm. For a coarse thread with no pitch given (just "M10"), the pitch is the coarse one in the table.

The rule is exact for the percentage: 76.98 × (D − (D − P)) ÷ P = 76.98%, for every size. Where the table differs from the rule (M8 × 1.25 → 6.8 instead of 6.75, M12 × 1.75 → 10.2 instead of 10.25), the drill is rounded to a stocked size. M8 with 6.8 mm gives 73.9%.

5.0M6 × 1 drillM6bolt 6 mm6.8M8 × 1.25 drillM8bolt 8 mm8.5M10 × 1.5 drillM10bolt 10 mm
Tap drills next to the bolts they are for, to scale. The gap between each pair is one pitch.

Substituting inch bits

If you only have inch bits, the last column of the table gives the closest one. For M6 a #9 (0.196 in) is just under 5 mm; for M8, 17/64 (0.2656 in) is 0.002 in under 6.8 mm, which raises the thread to about 77%. Avoid going smaller than the metric drill on M3 and below: those taps break easily.

Sources: Wikipedia, "List of drill and tap sizes" (inch and metric tap drills, clearance holes); Wikipedia, "ISO metric screw thread" (ISO 261 coarse and fine pitches, basic profile).

Metric tap drill chart questions

What size drill for an M6 tap?
5.0 mm for M6 × 1, the standard coarse thread. The rule diameter minus pitch gives the same: 6 − 1 = 5.
What drill for an M8 tap?
6.8 mm for M8 × 1.25. For M8 × 1 fine, use 7.0 mm.
What tap drill for M10?
8.5 mm for M10 × 1.5 coarse; 8.8 mm for M10 × 1.25; 9.0 mm for M10 × 1.
What drill for an M5 tap?
4.2 mm for M5 × 0.8.
What drill size for M12?
10.2 mm for M12 × 1.75 coarse; 10.5 for × 1.5 and 10.8 for × 1.25.
How do I work out a metric tap drill?
Diameter minus pitch. M4 × 0.7 → 4 − 0.7 = 3.3 mm.